Dynamic · Cross-platform

50160 S-CONNECT

TCP Unofficial
UDP Unofficial
SCTP —
DCCP —

What it is

S-CONNECT data exchange / device pairing.

When / why

Proprietary device integration.

Protocol status detail

TransportStatusMeaning
TCP Unofficial Not assigned by IANA, but standardized, specified, or widely used on this port.
UDP Unofficial Not assigned by IANA, but standardized, specified, or widely used on this port.
SCTP — Not applicable for this transport.
DCCP — Not applicable for this transport.
« 49152–65535 Ephemeral / dynamic range 51413 Transmission »

Port range

Dynamic / private (49152–65535). Cannot be IANA-registered; used for ephemeral allocation and custom services.

Browse all ports →

Firewall rules for port 50160

Copy-ready inbound rules for the active transports. Replace every <source> placeholder with the specific host, subnet, or CIDR that should reach this port.

ufw

sudo ufw allow proto tcp from <source> to any port 50160

Allow TCP 50160 (S-CONNECT). Replace <source> with the network/host that should reach it.

sudo ufw allow proto udp from <source> to any port 50160

Allow UDP 50160 (S-CONNECT). Replace <source> with the network/host that should reach it.

firewalld

sudo firewall-cmd --permanent --add-rich-rule='rule family="ipv4" source address="<source>" port port="50160" protocol="tcp" accept'

Allow TCP 50160 (S-CONNECT) from <source>. Run 'firewall-cmd --reload' afterwards.

sudo firewall-cmd --permanent --add-rich-rule='rule family="ipv4" source address="<source>" port port="50160" protocol="udp" accept'

Allow UDP 50160 (S-CONNECT) from <source>. Run 'firewall-cmd --reload' afterwards.

nftables

nft add rule inet filter input ip saddr <source> tcp dport 50160 accept

Allow TCP 50160 (S-CONNECT). Assumes table 'inet filter' with an 'input' chain.

nft add rule inet filter input ip saddr <source> udp dport 50160 accept

Allow UDP 50160 (S-CONNECT). Assumes table 'inet filter' with an 'input' chain.

iptables

sudo iptables -A INPUT -p tcp -s <source> --dport 50160 -j ACCEPT

Allow TCP 50160 (S-CONNECT). Persist with iptables-save/netfilter-persistent.

sudo iptables -A INPUT -p udp -s <source> --dport 50160 -j ACCEPT

Allow UDP 50160 (S-CONNECT). Persist with iptables-save/netfilter-persistent.

Azure NSG

az network nsg rule create -g <resource-group> --nsg-name <nsg> -n Allow-sconnect-50160 --priority 1000 --access Allow --direction Inbound --protocol "*" --source-address-prefixes <source> --destination-port-ranges 50160

Inbound rule for 50160 (S-CONNECT). Set <source> to a CIDR; lower priority number = higher precedence.

AWS Security Group

aws ec2 authorize-security-group-ingress --group-id <sg-id> --ip-permissions IpProtocol=tcp,FromPort=50160,ToPort=50160,IpRanges="[{CidrIp=<source-cidr>}]"

Inbound TCP 50160 (S-CONNECT). Replace <source-cidr> (e.g. 10.0.0.0/16).

aws ec2 authorize-security-group-ingress --group-id <sg-id> --ip-permissions IpProtocol=udp,FromPort=50160,ToPort=50160,IpRanges="[{CidrIp=<source-cidr>}]"

Inbound UDP 50160 (S-CONNECT). Replace <source-cidr> (e.g. 10.0.0.0/16).

GCP firewall

gcloud compute firewall-rules create allow-sconnect-50160 --direction=INGRESS --action=ALLOW --rules=tcp:50160,udp:50160 --source-ranges=<source-cidr> --network=<network>

Ingress rule for 50160 (S-CONNECT). Scope with --source-ranges and optionally --target-tags.

Windows netsh

netsh advfirewall firewall add rule name="Allow S-CONNECT 50160/TCP" dir=in action=allow protocol=TCP localport=50160 remoteip=<source>

Inbound TCP 50160 (S-CONNECT). Set remoteip to a host/subnet; 'any' is discouraged.

netsh advfirewall firewall add rule name="Allow S-CONNECT 50160/UDP" dir=in action=allow protocol=UDP localport=50160 remoteip=<source>

Inbound UDP 50160 (S-CONNECT). Set remoteip to a host/subnet; 'any' is discouraged.

Windows PowerShell

New-NetFirewallRule -DisplayName "Allow S-CONNECT 50160/TCP" -Direction Inbound -Action Allow -Protocol TCP -LocalPort 50160 -RemoteAddress <source>

Inbound TCP 50160 (S-CONNECT). Replace <source> with a host or subnet.

New-NetFirewallRule -DisplayName "Allow S-CONNECT 50160/UDP" -Direction Inbound -Action Allow -Protocol UDP -LocalPort 50160 -RemoteAddress <source>

Inbound UDP 50160 (S-CONNECT). Replace <source> with a host or subnet.

Rules are generated only for transports marked active for this port. They default to an inbound allow with an explicit source placeholder — never any. Review direction, scope, and rule precedence before applying in production.